old man emu Posted Monday at 06:08 AM Posted Monday at 06:08 AM 5 hours ago, red750 said: WD-40 is supposed to be the be all and end all of thread looseners. It wasn't created for that purpose. It was created as a water dispersant to remove moisture from NASA rockets. Hence the WD part of the name. The -40 arises from the fact that it was the fortieth mixture brewed up by the developers to do the job. There are plenty of other penetrants that do a better job. These range from the DIY 50/50 acetone/transmission fluid to stuff like Kroil and Mouse Milk. I've even seen stuck engine pistons freed by pouring in some kerosene and giving the top of the piston a bit of a tap with a hammer handle over a few days. Obviously in that sort of case, time is not a factor in the repair. I watch a lot of videos where people use WD-40 to free rust-seized nuts, bolts or screws. I often notice that as the threaded section of the fastener is exposed, it is not wet very far down the shaft. I reckon most of that is sprayed on just floods over the surrounding surfaces. Any proprietory penetrant is expensive - mostly in the cost of packaging and retailing. My preference is acetone and ATF. 1
Admin Posted Monday at 06:20 AM Posted Monday at 06:20 AM What about Penetrene? A mechanic friend of mine called it "Hens Piss" and always swore by it 2
facthunter Posted Monday at 08:04 AM Posted Monday at 08:04 AM There's a skill in freeing rusted nuts. Sometimes you split them with hole and a chisel. Other times heat them and force all the water out, Make it convert from Hydrated Iron oxide to the black one. Put some Penetrene there for a while and move it a bit both ways, till it frees up with a good fitting ring or socket spanner. . Nev
old man emu Posted Monday at 08:56 AM Posted Monday at 08:56 AM 48 minutes ago, facthunter said: move it a bit both ways One technique I have seen is to turn the nut, bolt or screw in the tightening direction a bit. That seems to break the "seal" caused by the rust. Doesn't always work, but worth a try before employing brute force and ignorance. I should add that you do this after letting some penetrating fluid soak a bit. 2 hours ago, Admin said: What about Penetrene? I was only trying to name a few penetrants. There's a million and one proprietory ones on the market.
facthunter Posted yesterday at 02:40 AM Posted yesterday at 02:40 AM I would NOT suggest moving it in the tightening direction first unless it fixing something like a fence Post. The heating is very effective with Wheel spokes. You can often save them that way. Nev
old man emu Posted yesterday at 05:45 AM Posted yesterday at 05:45 AM Not a big twist. Just a poofteenth.
facthunter Posted yesterday at 07:48 AM Posted yesterday at 07:48 AM Loosen it a bit FIRST, but the concept of moving it gradually in both directions is sound. It helps work the Penetrene or what-ever through the thread, and saves the Hex. from being rounded off, or the stud snapping. If in doubt drill a hole and split the Nut, both sides IF necessary. Stuff operating near Salt water can be difficult. Grade 4 Auto bolts are tough. Getting spark plugs out of alloy heads where no anti seize has been used is also tricky. A helicoil is not really a satisfactory FIX there, and a staked in threaded Bush isn't either. Prevention is better than repair. Nev
Litespeed Posted 12 hours ago Posted 12 hours ago When all else fails ... if you have access, use a stick or mig welder or spot welder to weld the top of the bolt shaft to the nut. The big heat surge makes it expand then contract and breaks the seal of rust. Used many times for bastard bolts. But be careful.. 1
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now